What have you done to your 5th Gen 4Runner today?

Fyre Flys from Amazon. Had them in my 20 AG Pro and had them in my 21 tundra. I like the brightness of them.

 

Dr. KDSS

 

Filled my SR5 up with gas.

 

I Raptor lined my sliders last spring. They will need a touch up after the winter and them getting a bit of sandblasting from driving on highways. At least Raptor liner is a lot easier to touch-up then powder coat.

 

the good doc!

 

Redline has a synthetic 75W85 which I saw at my local autoparts shop along with their 75W gear oil for the transfer case.

Redline 75W85
https://www.redlineoil.com/75w85-gl-5-gear-oil

Redline 75W
https://www.redlineoil.com/mt-lv-70w75w

 

Used same ones!

 

Drove it home from Express Park S. KPHL AP after being parked there since 5-Feb-24 4:30am

 

How much did money did the stealership extort out of you for that?
I want to do the same, my sway bar slides slightly side to side more than it should I believe, from incorrect angle at the bushings. Also prolly could use recentering while clamps are off.

 

$400 plus tax Just did not want anybody else to touch the kdss

 

My goodness
Just for billet clamps
Aren't they 110 bucks for the pair

 

Yup. What can you. They charged me two hours for the two pairs, front and rear. Stealerships. They had the excuse because some minor drilling was involved

 

Ahh I see, there's rear as well.
Ya I seen on the website it's a tiny drill bit, and 2018 and older you gotta trim a tiny bit of the bellow boot.
Without researching further, I feel like I can tackle this myself. I could be mistaken.
Happy for you tho dude, I haven't seen many folks running these on 4R .com but they're a smart choice

 

They are pretty beefy, now I will be confidently flexing

 

It looks like your door has a huge dent in it.

 

Was supposed to be heading out tomorrow morning to hit some trails up in the mountains but a project hit a snag. Does anyone know a better (easier) way to pull these damn square-pegged fender liner clips out? Several I can partially get to from the backside but some are in blind areas.

 

I friggin hate those
I wanna know this answer lol
Thx

 

They are a pain in the ass to remove. Sometimes I take a small flat head screw driver and put inside the hole and pry it out from one side.
Sometimes I take a retainer puller and pull the whole retainer slightly out and then use the flat head screw driver from the outside and push the clip inside so it can slide out. But mostly, I keep a bag of these handy and normally just replace them because I lack patience to take them out without damaging them and just yank them out. Just yesterday I had to remove my front passenger fender liner and I think I got 2 and broke 1.

 

I scored some pro suspension off of Facebook for only $500, off of a 2021 with 15k miles on it. They were in VA so I had to pay to ship them ($100) as well as add new top hats, because the previous owner reused them for his 6112 ($40). All in for $640, which in and of itself is a great deal, plus my 100k mile SR5 suspension was due for replacement anyways.

 

I lifted mine 2 inches and it’s level now. Big improvement and out on 33s

 

TRD Bro

 

After posting additions and upgrades to my build in this thread for the past 2+ years, not knowing there is a specific build section, I was asked by @Thacrow if I would consolidate the build in the build section. For those interested, I have. While the build is done and I am well satisfied with the outcome (especially after living in the 4Runner between Apr-Sep 2023 while working at night and sleeping comfortably during the day in the Arizona summer heat, and most recently traveling the NMBDR Jan 2024, the coldest being 7F), each adventure brings me back to the drawing board. I will continue to post additions and upgrades here with an invitation to the build thread (https://www.4runners.com/threads/4runner-converted-to-go-anywhere-rv.36487/#post-546459) for those who missed the first two years of the build. Hope that helps.

 

I like to use the kdss kill switch probably every month keep the fluids flowin'. Not many see this dash warning and its actually OK.
It's cool to experience the body roll.
This is my most expensive switch.

 

DrKDSS may have a good solution for all those who see the warning for real reason.

 

dr.kdss is doing some great work! Probably what Toyota should've done by installing a switch in the truck to disable kdss when wanted, beefier parts, rebuildable shocks, etc...

It seems like Toyota built KDSS only for pavement princess trucks since the main benefits is to reduce body roll, which is ironic that they put it on the TRD OR trims. Off road performance are negligible if not worse in stock form (slightly better front articulation, slightly worse rear articulation, terrible on washboards/ dirt roads at speed, prone to get damaged more easily off pavement, etc...) Kdss wouldnt be as great off pavement if it wasnt for his contribution. With his stuff, it becomes a great feature both on and off pavement

 

was it hard running/hiding those wires in the lights?

 

Mobil1 75W90 for me as well front and rear

 

I also use Redline 75W in the TC in my 2011 ( no issues) and at 50k in my 2022.