What have you done to your 5th Gen 4Runner today?

Installed the fangs today.

 

Swapped the TPMS nuts.

 

Thanks! Its for my solar panel connected to my dual battery setup.

 

Arb drawers are on my to buy list. @ATX14 they feel pretty solid?

 

That's easy: remove the mud flaps. They look ugly anyway.

 

Why does it matter when the 4Runner mud flaps don't have 4x4 on them?

 

My front mud flaps came off and rears were cut flush with the body within days of buying my 4R The old Tacoma also came with thin flaps that would, well, flap in the breeze. The 4R flaps are thick so if you do run them, they will not flap around and hit the tailpipe like the Tacoma flaps did. That's a lot of flapping............

 

lol yeah the 2015 did have stronger flaps. The early ones had what was basically just a flat piece of plastic and they would just fold back while going down the road. I personally hate the look of mud flaps so they had to go. The front were sold, rears I trimmed flush and put them back on. If they are removed, there is a big hole behind them so that wasn't an option for me.

 

Running boards came off right away also however you are absolutely right. I do have a number of rock chips on the bottoms of my doors which I touched up a couple days ago in prep for my fall detail. I guess the chips here and there are not bad enough for me to put flaps or steps on. They're so low on the door that if you're careful with touch up you can't see them anyway. I have the OEM touchup paint that comes with the tiny brush so it blends in really well. It is definitely a personal decision though.

 

Just got back from the shop. OME 3" and some DC 285/70/17

 

Sadly no, someone put a damn pinstripe on it. Its on my list of things to do but just further down the list. And to be fair, it looks better than my signature

 

Nice nuts

 

I just finished a week long off-road trip in New Mexico and they did great. No squeaking, drawers stayed open on inclines so no complaints. Still need to install my floor side kits that go with the drawers. The framework is metal so they have been solid with my limited experience. There are some good write ups on ARB installation online.

 

Good to hear. I heard the Dobinson drawers squeaks which sucks because I was planning to get them or ARB.

 

Got my windows tinted and put my sliders on.

 

Lmao

 

Where did you ordered these?

 

Link is below in this area. Not being a dick, I just know where to find it. Hope it helps.
Ryan.

 

https://www.amazon.com/dp/B00CXSVODO/ref=cm_sw_r_cp_awdb_btf_t1_OZZBFbPGDRKZ9

 

washed and waxed with soft99’s waterproof super wax looking decent for a change...

 

Quick install day yesterday: added the toyota bug shield and the raptor lights. Both really easy. Tbh the bug shield is only because I lost some paint at the very edge of hood due to a automated garage door at work (don’t even ask), so for 57 bucks- out of sight out of mind. Oh well...tires and wheels installed on Wednesday.

 

Tint and a little bit of elevation today

 

Went to the range yesterday to sight in my deer rifles. It's basically in a sand pit so it's very dusty since we've had no rain for a while. I did get to pop it into 4H for a little bit though! So today she got a bath and vacuuming to get all that dust off.

 

Body mount chop

 

Quick very short trail for the first time.

 

Gonna do high clearance cut too. Came out awesome. Triple c chop shop near Austin tx if you ever need work done

 

I got one of these yesterday..... Luckily my buddy owns a glass company and was able to seal the cracks before they run across the windshield.

 

I’ve got a super small one that I should get repaired. Been bugging me for months