What have you done to your 5th Gen 4Runner today?

Nothing! It's still sitting covered until I sell my 06 Tacoma.

 

For no other reason than my old man is thinking about unloading his Colorado, I checked Edmunds on my 23 and oof...that depreciation is a sumbitch

 

Exactly what I used. Did mine Friday. Such a cheap, easy, yet practical mod.

 

Do you have a final coat count? Did they come raw or are you resurfacing them from abuse?

 

There were rocks chips in the powder coat. Nothing bad, but since they are off the car I figure I would give it a fresh coat. I used purple power degreaser and 2 coats of truck bed liner. It's got a slightly textured feel to it.

 

That's exactly what I need to do, but I don't want to take them off ha

 

forgot i also swapped out some halogen for led's. the parking light led's worked great.
i swapped the DLR/signals and the LED's work in turn signal mode on each side, but when i turn the DRL on, they dont go on at all now? i put the halogen back in the left side and it also did not go on in DRL mode? i just left the LED's for the DRL in bc they are easy to access and i can mess with them later, but i dont know why that was happening...

 

One more job done on the DIY-maintenance-list: Power steering fluid changed.
Front brake pads and brake fluid should be replaced this weekend. If I get the vacuum extractor from my coworker.

 

I used a coin to show scale, and you brought yours out on a forklift! YIKE! That has to be some crazy amount of force. Amazing. Thanks for sharing.

 

new wheeels and tires!

 

Cleaned and chased bolt holes in the frame. It was tedious and probably wasn't necessary, but I can be sure of not having problems with a properly started bolt.

 

Got the Taco Garage Dash Mount installed. Super easy install and very well made.

 

I like the look of steelies on a White Runner. Nice!

 

Installed my new roof rack.

 

Traded in my white 23 ORP for a 24 silver LE.

Will take some better pictures.

1st will need running boards. Anyone recommend some that don’t hang down so low? I’ve seen some posts that say to use SR5 bracket and running board b/c the bracket hangs down less. I’ve seen some recommended a N-Fab nerf step kind that supposedly hangs down less.

2nd will be windshield and front side window uv block.

3rd possibly hood and bumper PPF

4th TRD pro wheels and 255/75r17 AT tires

5th amber LED fog lights

 

Your concept drawing sort of reminds me of this drawing.

 

3/8" Nylon barb from Tractor Supply....$2.75
10" of 3/8" hose (any kind) from auto parts house (cut from their reel)....$1.00

 

My personal opinion -

1st will need running boards. - I dislike running boards on 4Runner Limited. They look ugly to me. I prefer Automatic running boards, but may not be as reliable. Mine are working for 5 years but who knows when they might fail?

2nd will be windshield and front side window up block.- Are you talking about tint? In the past I did 70% 3M crystalline tint on my windshield and it was too dark to my taste driving at night. For my 4Runner I did 90% 3M crystalline tint and it was perfect for me. For sure at night nothing better than any tint. For the 2 front I asked the tint shop to match the rear. But in summer I wish I go little darker yet I don't want illegal level of darkness.

3rd possibly hood and bumper PPF - I dislike the PPF installed by Toyota dealer on my previous car as it got yellowish with time. That car was white so it was little ugly. I have AVS bug shield on my 4Runner and so far no complaints.

4th TRD pro wheels and 255/75r17 AT tires - I'm not a fan of TRD Pro wheels and skinny tires. I like wider TRD offroad wheels and to my eyes they really match a Silver 4Runner. I specifically picked TRD offroad wheels because they meet the spec to run bigger tires. As stock I would much prefer P265/70R17 tires to complement the look of 4Runner.

5th amber LED fog lights - I dislike amber lights are they have less light output than white. I can also run white on daily basis without annoying other drivers. And stock white TRD Pro fog lights works pretty well on foggy conditions so far with my experience. (Fog lights are little different from trim to trim). Changing fogs on a Limited is not easy as SR5/TRD ORP. For my Limited that came with halogen fog lights I changed to TRD Pro like fog lights.

 

@djwantke finally got it in the shop TODAY to get rims put on. Also getting an alignment while at it. Steering wheel had a small wobble while driving I've noticed over past few weeks. Will post pics after I get Casper back.

 

Throttle body and mass air meter clean, Front diff fluid change & while I had the skid off, put some Amsoil MP HD on the top side, wire wheeled up underneath and applied some protectant. Next week will do the trans fluid and filter change.

 

Just installed a Midland MXT575 (hidden) with a ghost antennae. I have not yet tested it, but it does power up so hopefully everything will work properly.

 

Info on hood bug deflector? Amazon? Easy to install? No holes to drill?

 

If you want to try reaching the Springs let me know when and which channel and I would be happy to hop in my rig and see if I can hear you. Are you by chance on the Pikes Peak 650 repeater? That would boost our chances of a successful radio check.

 

AVS, ordered from RealTruck. very easy install, uses preexisting holes on the bittom lip of the hood. If I had to do it again I would also apply PPF to the areas that touch the hood bc I did chip the paint in a few places.

 

Put non-functional buttons on my steering wheel

 

im curious as well. It’s been done many time with no issues.
Is it easier to replace everything than welding a 3 bolt flange? Yes, but that’s the reason we go to an exhaust shop. If I replaced everything I wouldn’t need to pay someone to install it. How much are they charging you? Maybe they’re just being lazy and want easy money by bolting instead of cutting and welding?

 

Finally had a chance to install my Father’s Day gifts today. Canvasback liner and Weathertech smoked window shades.

 

Replaced hatch speakers. Installed a couple dual knobs into the center console plastics.

 

Ordered a set of TRD Pro rims but being told they are on hold.

Now I get to wait.