What have you done to your 4th Gen 4Runner today?

No I didn't

 

We cut ours, leaving the tops, I gotta clean them up but it gets rid of the gap.

 

Thank god for this 4Runner or I would be losing my mind. Took the rust out of the bumper and painted it. Fixed the fog lights. Going to have to replace the turn signal lights as well, sockets are basically brittle. Winch arrives today. I may be broke once this all blows over but at least I will still be sane lol.

 

Out with the old in with the new!
Before:

After:

 

Those are siiiiick. Wet okole? Catskinz?

 

Neither they are a brand the dealership is selling here locally. They have no brand lol not that I’ve found but I’ll look around. The are neoprene and fabric covered. I’ll see if I can find out who makes them for ya lol

 

Nice work. I also have the “clunk” on my “new” 04 Limited. Can you point me towards info on the cause and your solution? That would be awesome! Also just switched out my old pink taillights for those same ‘06s. So much happier with them

 

After 243k miles it was time to replace the valve cover gaskets. While I was there I decided to do some cleaning and painting.

 

What paint did you use?

 

VHT Engine Enamel

 

easily get another 200k more! ! awesome stuff

 

Well it took off and on a year to complete but it is finished and installed this grill. All fabrication and paint work done by me. I think it looks so much better.

 

Shiny new front passenger wheel bearing to replace the growling wobbly one that was on there.

 

Got all my new lighting done up front yesterday.
Fogs - Baja Squadron Sports (WC)
Ditch lights - Baja Squadron Sports (WC)
Bumper - Left over Amazon light from Tacoma
CBI - Ditch light brackets
Caliraised - Flush mount brackets
Low beams - 6k HIDs
Caliraised switches

 

I know its been awhile but I was wondering what rims those are? I’m looking for something like that. Thanks in advance

 

They are MT wheels https://www.jegs.com/p/Mickey-Thompson/Mickey-Thompson-Classic-III-Black-Wheels/2352417/10002/-1

 

I installed Rad Rubber Design engine splash guards. I really like them. They are so thick but flexible.

 

I installed Rad Rubber Design engine splash guards. I really like them. They are so thick but flexible. Here is a picture. Note, the tool is mine and was not included.

 

2004 Runner SR5.
I found why my AC pump bolt was weird. Broke in half.
I’m engine swapping. 142k and the timing chain bombed.

 

Adapted a phone mount idea that Lawndart described on Instagram recently. Much more sturdy than the Scosche Magic Mount I was using; you can see the old mount on the dash still.

 

Finally got around to installing my Overland Equipped fuse block bracket with block, circuit breaker, etc. Had to chop up the leg a bit to clear the brake lines.

 

I need one of these.

 

Finally did my satoshi grill.

 

Do yours smell like cigarettes? Ours did when we first got them lol

 

OMG mine stank so bad too. I went to visit my parents after having them just sitting in the back of my car for a few days and my mom asked if I'd taken up smoking.

 

Hahaha bad stank. It went away though after a few weeks

 

We had the same clunk that went away when we replaced our panhard bar in the back.

 

New 4x4 off road decals and badges, as well as 20% tint all the way around....still not 100% sure I like the badges yet, looks better in person up close.

 

Replaced both lower control arms. Converted Xreas to regular suspension using Bilstien shocks and FJ cruiser springs. Next is new fender liners and locking rear differential.