1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Making a list of parts, suggestions?

Discussion in '3rd Gen 4Runners (1996-2002)' started by jross20, May 23, 2019.

  1. May 23, 2019 at 9:16 AM
    #1
    jross20

    jross20 [OP] New Member

    Joined:
    May 20, 2019
    Member:
    #9958
    Messages:
    96
    Gender:
    Male
    So I'm making a list of parts to acquire over time for my upcoming 3rd gen overland build. Just wanted to see what kind of things you guys would suggest I look at.

    Already planning on sliders, arb bumpers, a roof rack, new u-joints. But I'm not sure what suspension setup I want to try to go for. And then I'm curious about lower ball joints, control/trailing arms. What goodies do you guys recommend? Are there better aftermarket parts for the arms and joints?
     
  2. Jun 18, 2019 at 12:09 PM
    #2
    MStudt

    MStudt New Member

    Joined:
    Jun 18, 2014
    Member:
    #174
    Messages:
    163
    Gender:
    Male
    First Name:
    Mike
    Eugene, Oregon
    Vehicle:
    01 SR5 4runner
    3" Toytec/Eibach, OME 891's, Custom Skid, Falken 285/75/16
    The real question is what are you building it for? Overlanding is pretty vague. To some overlanding is decking out your 4runner with every since piece of aftermarket items under the sun. To others, is equipping your 4runner with what you need to live out of.

    Mike
     
    Last edited: Jun 18, 2019
    SlvrSlug likes this.
  3. Jun 18, 2019 at 9:21 PM
    #3
    jross20

    jross20 [OP] New Member

    Joined:
    May 20, 2019
    Member:
    #9958
    Messages:
    96
    Gender:
    Male
    Ah I got you. Well, basically she is going to be our road trip and trail rig. Some day we want to take her through the huge public parks and camp in her. But for now I am just getting her ready to go off-road. Looking at suspension stuff right now, shocks, coils, control arms, and then eventually skids and sliders.

    Other than fun stuff, I also want to know if there are any items I should replace or upgrade, like... Joints or bushings?
     
  4. Jun 19, 2019 at 6:57 AM
    #4
    MStudt

    MStudt New Member

    Joined:
    Jun 18, 2014
    Member:
    #174
    Messages:
    163
    Gender:
    Male
    First Name:
    Mike
    Eugene, Oregon
    Vehicle:
    01 SR5 4runner
    3" Toytec/Eibach, OME 891's, Custom Skid, Falken 285/75/16
    I'd replaced your upper ball joints, lower ball joints (OEM ONLY), inner tie rods, and outer tie rods. I'm a big fan of OEM parts when it comes to what I just mentioned. They tend to last quite a bit longer than Moog, and the other crap. If you've going to lift it you'll want to replace your CV boots on the front while you're installing the lift. If not, you'll be doing it shortly after the lift when the rip open.

    You can upgrade your front upper control arms if you want, but that isn't needed. SPC makes good non-uniball uppers, and that's what I would recommend. I don't see the point in swapping out any of your rear control arms unless you have bad bushings or something like that. You might want to consider upgrading your sway bar links to longer one to accommodate your lift (contact me if you need these).

    Mike
     
    jross20[QUOTED][OP] likes this.
  5. Jun 20, 2019 at 7:54 AM
    #5
    jross20

    jross20 [OP] New Member

    Joined:
    May 20, 2019
    Member:
    #9958
    Messages:
    96
    Gender:
    Male
    Lower ball joints done! And don't worry I always use OEM, especially since they are made in Japan or the USA. Are the upper ball joints swapable or do I need to change the whole arms like the 2nd gen taco's?

    CV boots, got it. Is there anyway to check the CV joints to ensure they are fine while I am doing this? Can I grease them?

    I also have to replace the street ng rack, is there an oem kit that comes we the the tie rods as well?
     
  6. Jun 20, 2019 at 10:14 AM
    #6
    MStudt

    MStudt New Member

    Joined:
    Jun 18, 2014
    Member:
    #174
    Messages:
    163
    Gender:
    Male
    First Name:
    Mike
    Eugene, Oregon
    Vehicle:
    01 SR5 4runner
    3" Toytec/Eibach, OME 891's, Custom Skid, Falken 285/75/16
    Just buy new upper ball joints. You can use a pickle fork to separate the upper control arm from the ball joint. Then press out the upper ball joint from the spindle, which can be a pain, but pretty straight forward.

    You can but GOOD boots from ORS, and grease packs too. Clean the joints, and apply the new gease before rebooting them. A lot of people use A1 for steering racks now since Safari went out of business, and none of them come with tie rods either.

    Mike
     
    jross20[QUOTED][OP] likes this.
  7. Jun 20, 2019 at 6:42 PM
    #7
    4Running Daily

    4Running Daily New Member

    Joined:
    Apr 6, 2014
    Member:
    #21
    Messages:
    60
    Gender:
    Male
    If you're interested in SPC upper control arms, feel free to shoot me a PM. Happy to do deals for forum members.
    https://www.srqfabrications.com/product/96-02-4runner96-04-tacoma-spc-upper-control-arms
     
    MStudt likes this.
  8. Jun 20, 2019 at 7:12 PM
    #8
    jross20

    jross20 [OP] New Member

    Joined:
    May 20, 2019
    Member:
    #9958
    Messages:
    96
    Gender:
    Male
    Ordered the oem ball joints!

    Hey man your site has some awesome stuff on it, I bookmarked it for later. I appreciate the offer but I am partial to JBL UCA's since I've had such great success with them on my taco.
    I am eyeing your stainless steel skid plate.... man that looks good.
     

Products Discussed in

To Top