1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

DIY Chase Lights

Discussion in 'Lighting' started by Cis915, Feb 2, 2024.

  1. Feb 2, 2024 at 7:45 PM
    #1
    Cis915

    Cis915 [OP] New Member

    Joined:
    Apr 25, 2020
    Member:
    #13983
    Messages:
    45
    Gender:
    Male
    First Name:
    Donovan
    Las Vegas
    Vehicle:
    '18 Nautical Blue TRDOR
    Eibach Pro Lift; 255/80 Open Country R/T Trails; Motegi Trailite; LFD 7/8; BMC/Pinch Welds; All-Pro Sliders; Custom Drawers; T10 v3; DD SS18 Light Bar; Baja Squadron Pro Ditch Lights; Auxbeam Switch; Alpharex Headlights; Spyder Taillights
    TLDR: Made some chase lights with parts from Amazon and a 3d printer.

    I was on a trail with some friends the other day and realized the importance of having chase lights. Didn’t want to spend a ton on them and I like doing DIY stuff, so this is my project, written up for the internet to enjoy…

    Don’t think I need to explain the utility of chase lights too much, but basically these are rear facing lights that allow a following vehicle to keep track of you during low visibility conditions, i.e. dusty, snowy, rainy, etc. They’re usually mounted high up, away from the dust cloud that your tires are stirring up. I wanted mine to flash, to make it even easier to follow me, but I suppose you could keep them steady. I’ll be controlling the lights with my Auxbeam Switch Panel. The side quest of this project is to clean up the current wiring of the switchpanel under the hood, as it is currently very ghetto.


    PARTS
    Lights:
    - Cheap Amazon Special ($20)
    Wiring:
    -Wire ($13)
    -DT Connectors ($16)
    -2-1 DTConnector ($11)
    -Strobe Module ($9)
    Misc.:
    -Wire Tunnel ($27)
    -Custom Module Enclosure: $0 (3D Printed)
    Already on-hand:
    -Various Nuts/Bolts
    Total: $97
    upload_2024-2-2_19-34-8.jpg

    DESIGN
    Connecting two LED pods together and running them to a single switch on the Auxbeam panel is pretty straightforward, the only “complicated” part was adding the strobe module to make them flash. Because the module I bought isn’t waterproof and I didn’t want it dangling freely under the hood, I designed and 3D printed an enclosure that could be mounted near the switch panel under the hood. For the harness, I opted to use DT connections to make the lights easy to remove for maintenance or if I wanted to upgrade later, while also keeping some weather/water resistance. I have an LFD 7/8th’s roof rack that will serve as the mounting point for the lights, using provided hardware.
    upload_2024-2-2_19-35-37.jpg
    upload_2024-2-2_19-35-27.jpg

    WIRING

    upload_2024-2-2_19-21-35.png

    As anticipated, this was pretty straightforward, except that the strobe module has a single positive output and two negative outputs. According to the module, the red wire is meant to be shared between the two lights, while each negative will connect to a single light. After some garage R&D, I found you can combine the two negative output wires together and the lights will strobe simultaneously. If you connect the lights as instructed in by the module, they will flash alternatively, i.e. the left will strobe for a second, then the right, then the left, ect. I prefer the simultaneous flashing that I got with my method, but either way works, you would just have to change the setup of the DT connections.


    I started by adding the DT Connections at their respective points according to the diagram above. I soldered the two black output wires (from the module) together prior to installing the DT connector to the module, then I added terminals to the input wires on the module. After adding the connectors, I laid the whole thing out next to the truck and tested it prior to installation.
    upload_2024-2-2_19-36-37.jpg

    upload_2024-2-2_19-29-46.jpg

    INSTALLATION
    Installation was simple enough, I started by mounting the lights and worked my way forward, using zipties to tidy the harness to the rack . Once I fed it under the hood I let it dangle and started working on cleaning up the wiring and mounting of the switchpanel and the 3D enclosure. Didn’t take pics of this process, but I unmounted the current switchpanel, removed the mounting plate, and drilled four new holes. I cut some of the excess wire out and recrimped/soldered where needed. At this point I installed the module and enclosure onto the same plate as the auxbeam panel, tidied up all the wiring and connected the dangling harness to the module. Finally I installed the KC Hilites wire tunnel and tucked the wire into the channel.

    Old Wiring:
    upload_2024-2-2_19-37-2.jpg



    New Wiring:
    upload_2024-2-2_19-37-19.jpg


    COMPLETED PICS:
    upload_2024-2-2_19-38-54.jpg
    upload_2024-2-2_19-39-5.jpg


    REVIEW/LESSONS LEARNED

    All in all this was a cool project that took me about a week from first thought to completion and I'm happy with how it came out. Once I had all the parts, wiring and installation took about 3.5ish hours. Cleaning up the current mess of wires took about an hour and a half, so I’d say it could easily be done in 2 hours. I think the lights look great! I was worried about them being a little big, but I think they are tucked away nicely.

    If I had a SwitchPros or SPOD panel, I wouldn’t have had to deal with the strobe module because both of those have a strobe function built in, but I had fun designing and printing the enclosure. Besides, I really needed to clean up the switchpanel.

    If anyone wants the STL file for the enclosure, I'll try to attach it here.

    Thanks for following along!
     

    Attached Files:

To Top