Fumoto Drain Valve

Anyone know if the longer nipple version fits with the stock skid plates? I have one on our outback and it super nice to be able to attach a hose.

 

https://www.4runners.com/threads/metal-oil-filter-housing.25404/page-3#post-388818
read on, MacDuff

 

We had the long nipple version on our 2020, it fits, it's not as much clearance as I would like but it works. The long nipple has been replaced with the short nipple, (

$36 F133S with LC-10 S-Series Large Body FUMOTO Valve with Short Nipple and LC-10 Lever Clip for 12mm-1.25 Gold

F133S) it's just a piece of mind thing, a little more clearance for when that nasty rock hits the skid plate and bashes it in.... it could happen.

 

I have the short nipple version and it worked fine with the stock skid plate. It also gives about 1” of clearance on RCI skids - I know as I replaced the factory skid with RCI….

cheers,
Bob

 

Thanks guys. I'll go with the short model.

 

While I have your attention... are the skid plate bolts on a sr5 M8x1.25 20mm long?

I was thinking replace them with stainless. I found that size for some older generations. Wasn't sure on a 5th gen.

Once I actually have my 4Runner I'll be able to look. Should have it tomorrow morning.

Once again. Thanks fellas

 

Wouldn't clearance with the RCI skid be a non-issue, since the hole in the skid is directly below the drain plug?

 

You'll have to use anti seize with stainless bolts anyway to prevent galling. Just use anti seize on your steel bolts and save your money.

 

I planned on anti seize either way. I guess if the stock blots seem to thread fine I'll just use them for a while.

 

You would not want the nipple to extend below the skid plate. that would be a recipe for disaster.

 

The longer nipple vs. the short nipple version of the Fumoto valve is 10mm (.39 inches) longer. So if the short version gives 1" of clearance from the RCI skid, there's no possibility of the longer version extending below the skid plate.

I'm not saying longer is better, just that it doesn't extend below the skid.

 

No, the longer version wouldn’t extend below the 2” round oil drain opening in the RCI skid plate. That said, the possibility of a pointy rock dragging over the oil drain opening in the skid and hitting the drain nipple is reduced with the short nipple.

I’d rather have the extra margin of safety…

Cheers,
Bob

 

Since I don’t ever plan on putting a hose on the valve when changing the oil, and the oil drains straight out the bottom of the pan, I purchased the valve without a nipple.

P/N

$35 F-133 : STANDARD VALVE WITH 12MM-1.25 THREADS WITH LEVER CLIP Gold

F-133

 

I like the

$40 Fumoto F103SX M12-1.25 Sx Series Drain Valve, Bronze

F103SX valve but it really wants to have a hose attached

 

That's the new model and it drains 30% faster than the old ones. It's on my short list.

 

This is the one I have. I'm happy with it.

 

Do you have aftermarket skids? Does it spill in the skids since it doesn’t have the short nipple? I ask because I have this one also just waiting for oil change time but I noticed some guys installed the one with the short nipple.

 

I have SOS skids. It drains straight through the hole in the skid. It pours out in a clean stream, so nothing splashes the skid that I've noticed.

 

Ditto for the RCI skids….

Cheers,
Bob

 

I have RCI skids waiting to be installed at my next oil change.

 

I removed mine and switched to a suction thing from the dip stick.

 

I have an older short nipple about 7 years old. 3/8 fuel line works just fine w my SW skid. I have to change my oil in the driveway and the first time I changed with the Fumoto installed, the wind moved the stream around, so oil went all over the skid. Had to drop it and clean it up. So I started using the hose.