1. Welcome to 4Runners.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all 4Runner discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other 4Runner owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

C4 overland bumper

Discussion in '5th Gen 4Runners (2010-2024)' started by Gyoaz, Sep 15, 2020.

  1. Sep 15, 2020 at 7:12 PM
    #1
    Gyoaz

    Gyoaz [OP] Garyo

    Joined:
    Jun 1, 2019
    Member:
    #10124
    Messages:
    140
    Gender:
    Male
    First Name:
    Gary
    AZ
    Vehicle:
    5th gen 4runner TE
    Diff breather, Camburg UCAs, dobinsons 3" lift, front n’ rear steel, RTT, scuba exuiped, OBA, and some lights
    Just installed this beast, it’s pretty rad74AE20D0-A92C-4085-B9FB-B2A97567EB7F.jpg7F333E31-624D-4066-95BA-5F6436CA016A.jpg
     
    Doglover2003 and DreamsComeTrue like this.
  2. Sep 16, 2020 at 7:08 AM
    #2
    Ironguy

    Ironguy New Member

    Joined:
    Dec 22, 2019
    Member:
    #12421
    Messages:
    7,205
    Gender:
    Male
    First Name:
    Ralph
    Bisbee AZ
    Vehicle:
    2020 Black 4Runner Venture 1967 FJ40 Land Cruiser
    New pine scent hanger, new sun shade
    Looks good! I have been eyeing that same bumper for awhile. Any troubles getting it put on?
     
  3. Sep 16, 2020 at 7:47 AM
    #3
    Gyoaz

    Gyoaz [OP] Garyo

    Joined:
    Jun 1, 2019
    Member:
    #10124
    Messages:
    140
    Gender:
    Male
    First Name:
    Gary
    AZ
    Vehicle:
    5th gen 4runner TE
    Diff breather, Camburg UCAs, dobinsons 3" lift, front n’ rear steel, RTT, scuba exuiped, OBA, and some lights
    It wasn’t too bad. There are a few more parts than I was expecting but they allow to adjust the reveal to match the factory body lines very well.
     
    Doglover2003 likes this.
  4. Sep 16, 2020 at 8:34 AM
    #4
    Ironguy

    Ironguy New Member

    Joined:
    Dec 22, 2019
    Member:
    #12421
    Messages:
    7,205
    Gender:
    Male
    First Name:
    Ralph
    Bisbee AZ
    Vehicle:
    2020 Black 4Runner Venture 1967 FJ40 Land Cruiser
    New pine scent hanger, new sun shade
    How about the plastic cutting to remove the factory parts? Any lining up or cutting issues?
     
  5. Sep 16, 2020 at 10:32 AM
    #5
    Gyoaz

    Gyoaz [OP] Garyo

    Joined:
    Jun 1, 2019
    Member:
    #10124
    Messages:
    140
    Gender:
    Male
    First Name:
    Gary
    AZ
    Vehicle:
    5th gen 4runner TE
    Diff breather, Camburg UCAs, dobinsons 3" lift, front n’ rear steel, RTT, scuba exuiped, OBA, and some lights
    I just had to hammer the pinch weld in the wheel well and drill a couple of holes. No cutting.
     
    Doglover2003 likes this.
  6. Sep 16, 2020 at 11:49 AM
    #6
    Ironguy

    Ironguy New Member

    Joined:
    Dec 22, 2019
    Member:
    #12421
    Messages:
    7,205
    Gender:
    Male
    First Name:
    Ralph
    Bisbee AZ
    Vehicle:
    2020 Black 4Runner Venture 1967 FJ40 Land Cruiser
    New pine scent hanger, new sun shade
    Unfortunately my 2020 model has a plastic caboose.
     
  7. Sep 16, 2020 at 7:10 PM
    #7
    Doglover2003

    Doglover2003 New Member

    Joined:
    Sep 12, 2016
    Member:
    #2655
    Messages:
    456
    Gender:
    Male
    First Name:
    Nick
    SoCal
    Vehicle:
    '18 ORP w/KDSS
    Looks great! That's the rear bumper I want :thumbsup:
     
    Gyoaz[QUOTED][OP] likes this.

Products Discussed in

To Top