What have you done to your 5th Gen 4Runner today?

It is however it does not flow as well as the TRD Intake. The TRD intake did make a slight difference. Nothing crazy but you shouldn't expect anything crazy.

 

Yes it is Jason, I just added Too it with the Accelerator Horn and The Filter.
I notice a difference in acceleration when taking off from a stop. I enjoy experimenting with factory engineered Parts.

The way I spend my Doe is no concern of yours. ​

 

I was there last weekend. Fun times.

 

Finally painted the end caps on the roof rack matte black! So much better. Thank you Krylon Fusion!

 

Its dough not doe

 

Did you remove them to paint or do it on the vehicle. I want to do mine but just haven’t decided on either paint or use the super wrap product https://getsuperwrap.com/?gclid=EAIaIQobChMIw-z-3PLC5QIVrP7jBx04ngDHEAAYASAAEgILf_D_BwE

 

Removed them. Only one gave me some trouble. The trick is to find the right angle and pull ever so gently. The tabs came off fairly easy. Went on even easier. All in all it was probably a 30 min project (not including dry time). I let mine sit for 24 hrs before putting back on. So much better than the silver! Will see how the Krylon holds up.

 

I wonder how they determine which colors to use on which vehicles. My silver SR5 came with black end caps... Though id rather the entire thing was black... Just not enough to paint or wrap it.

Ordering falken wildpeak 285s on Thursday and my lift install and alignment is on Friday...After that the last thing left to "finish" my simple build is either doing the roof rack delete mod, or adding a couple crossbars... Still really undecided on which to do.

I wont really ever be throwing anything on top of my 4runner, i will just use a trailer when needed... But also not sure if i will think the 4runner looks right without the factory bars on it. And with the factory bars, i think it needs crossbars to at least look functional.

 

I hear ya! I would love to have the rails all black, but kind of like the silver contrast.

 

The best tool to remove the end caps is a paint can opener you can get at Lowe’s for a buck fifty. It’s just the right size to fit under the cap and pull the tabs loose.

 

That’s what I used. Most paint stores will give you one.

 

I bought a 20 peice pry tool kit with a zippered pouch for 8 bucks on Amazon works well

 

Ok i checked my orders, it was actuallt 18 bucks for 23 peices. Either way still affordable.

 

I was going to put the lift on tomorrow... But ended up with extra time today. 1 down. 3 to go.

 

Put it on the lift to put the lift on

 

My 2018 silver has silver end caps. I wish they were black.

 

A regular 4 post lift would be difficult LOL. But this is made for lifts and tires. There's cross section jacks between the ramps. Makes it easy. I wouldn't want to use this for normal work... But for lifts and tires it's the ticket. There's a 2 post lift right beside me... But I prefer this setup.

We're about done now. Then I'll drive it over to the alignment shop.

 

I'm about 3 hours from the Boat...

 

All done. Aligned up within specs no problem. Took about an hour and a half to install the lift and about 20-30 minutes to align.

Stopped and got some BBQ after alignment, took a picture there and the 4R looked a little high in the front... So I went to my garage, where the ground is perfectly level, and did some very scientific measuring... I concluded it's level enough for me. The level showed good no matter where I put it and my eyes agreed... If it's not perfectly level, it's so close I can't notice it with my eyes. I'm happy. There's a little bit of driver's side lean... But I didn't notice it until I was really looking for it.

Eibach pro kit, 2.75” front and 1" rear, gets the nod from me. Drivesa and looks good.

Tires ordered. Should be here next week and after installed I'll take some nicer pictures.

 

Nice...! lookin good

 

Hey guys we are getting an early start to our Black Friday deals!
https://www.4runners.com/threads/black-friday-2019-sale-20-off-early-bird-special.11362/

 

Really like the increased Fuel mileage since Monday. I run 90 octane Non Ethanol.

 

I assume yo

I assume you're completely stock otherwise? This mileage is pretty average for highway traveling when totally stock. Mine was modified right away so I have no idea what I got stock but my dad bought a 2019 and took a road trip shortly after. If I remember correctly, he was getting 23-24 on the highway with zero modifications.

With my current setup, best I have done is 18 with cruise set at 65 and driving about an hour and 45 minutes.

 

Yes all but the rear Fox Shocks. This is local Stop and go in town Traffic. It was always around 20.8. It’s still breaking in.

 

Maybe after a couple weeks the front will settle a half inch+ ? Might end up exactly where you want it.

 

Added my Morimoto headlights!!!!! So awesome!

 

Well on Wed. I put on the steps. Today I put on some flags.

 

Installed my rear window molle panels from Bullet Proof Fabricating. Pretty easy install. Now to get everything mounted up to them.

 

Looks good, ragofab had a shelf on sale this week. I like the setup with it attached to the side panels

 

They look great, just can't pull the trigger. So much $$$. and too much else to do.