What have you done to your 5th Gen 4Runner today?

I have their PCK and like it. Works great and no welding.

 

I installed my Cali Raised Catalytic Converter Covers that I received a while back. Shipping was very fast, and everything was packed well. Both sides fit perfectly, and installation was a breeze. I did install an extra washer or two on the outside transmission bolts to help align the front rubber bumpers to my frame. Placed my jack under the transmission bracket and put light pressure on it until both bolts were loose making swapping of the bolts easy. Also, I left one of the rear crossmember bolts loosely installed so I could just swing the crossmember out of the way and then swing it back to help the install process. I could not find extra secure bolts on the Cali site, but I will find some and install them soon. Very happy with this awesome product and the peace of mind!

 

Hand washed and hand dried the 2018

 

Ha! When it arrives I will ask her to lay down in it and report back the response! LOL

 

Contact Jake from Cali you can get extra bolts I did. $10.00. They don’t show them on the site.

 

Don, Thanks for the info!

 

No problem Jim, That way you have all. Security bolts.

 

Long-time listener, first time caller. A few upgrades on 2023 4Runner TRD Offroad:

Alpine INE-W970HD
JL Audio XDM700/5 Amp
JL Audio CP 108LGW3v3 Subwoofer
All speakers upgraded

Roofnest Condor Overland 2
RakAttach and One-Up bike rack

 

State inspection at the dealer near my house (who I purchased from), and was surprised to see 4 4Runners on the lot. Three ORP’s and a Pro, and one didn’t even have a sunroof.

 

do you need to remove these with rear tires off the ground?

 

Did the initial 1K oil change, top off, tire rotation etc. Making sure to get any tiny metal that may be lose from the assembly line.

 

The job can be done with weight on the axle as long as the LH and RH sides are even height, so the sway bar isn't preloaded. Typically you need to remove the wheel for tool access. On a new rust-free truck you may be able to do it with the wheel attached. I jacked up the LH side of the axle to remove the wheel, then lowered the jack an inch so the axle is level with the ground.

 

Nice Setup, and Welcome to the group!

 

Need to grab a photo, but over the weekend washed the truck and then did a coat of Wolfgang SiO2 sealant, let it set up and buffed off. 24 hours later a second coat, I’m a big fan of the Wolfgang products as I’ve been using them over 20 years.

 

And then today did my Waxoyl Hardwax Plus undercoating on my frame and various metal bits. Got a bit on myself, luckily eye protection and an N95, but very gratifying to get that applied. Only time will tell how it holds up but have only read good reviews on the product.

 

How did you go about spraying that?
I'm picturing truck-on-a-lift, but wondering if it's possible to do it without a lift.

 

Front wheels on ramps, low profile creeper underneath (with a large tarp below that). It actually was very easy, but would have been much easier on a lift so you could actually look aroud without being so close to everything but all in all wasn't tough.

 

those are new skins, replaces the soft tex...
I customized them here
https://www.canadaseatskins.us/toyo...024-toyota-4runner-katzkin-leather-seats.html

got full ultimate leather, two tone- dove grey faces and black bases, red stitching, perforated inserts only, and TRD Pro in red on the seat backs

leather was $1800, install was $600...

Got the install from a guy the dealer uses in Hurst TX

 

Welcome!

 

It was a bit of a wrestling match, but the Westcott Designs rock sliders are installed!

 

Replaced oil and filter, rotated tires, greased driveshaft and installed new wiper blades on the 2018. Had Bosch wiper blades but went back with Toyota wiper blades.

 

Toyota dealer had a tire sale going on. Got four new tires mounted, Road Force balanced, road hazard, and tax for $1067.00 out the door . Took it up to 75mph on the way home and dead steady, zero steering wheel shake .
Ridge Grapplers are dated 30/24.

 

Nice. Looks like they are angled up a little bit ?

 

More info on these, they look great. Enough sticking out to be used as a step? My wife thinks we need running boards. Little does she know they'll be rock sliders..

 

My wife is technically a little person. We got BAMF sliders. Flat ones with the solid plate on top and work very well as a step. Their coating is the best, toughest powder coating Ive seen, except that its a bit grey. Took me a little bit to get used to but I like them.

My wife thought they were "steps" for a long time.

 

I've been eye balling greenlane sliders. Aluminum so they're light and won't rust. Hard time finding photos of them on 4Runners. I know hard core wheelers chit on aluminum but let's be serious here...they're going to be used as a running board for my wife and kids...and hopefully look cool.

 

In the same boat, my wife likes the Predator Steps but they will get destroyed first even semi-offroad adventure. I've been eyeing the Westcost Designs 0 angle sliders, the video I found on them even states they stick out a little further than normal to ensure a decent step. Has my interest.

 

Here are some. I have the bump out on mine.

 

Would be cool to see some of these in person but we live in a 4Runner free zone haha. Just not a lot of them around and the ones I do see are bone stock and driven by a middle aged ladies haha.