What have you done to your 5th Gen 4Runner today?

We finally got the the wife's 2017 TRD OR 4runner out on the trail for some light wheeling, at MO4WD.com's 5th Annual Stocker No Locker event sponsored by MT Schiele Auto Repair.

 

I agree! … Curious, what did you go with?

 

Thanks for all the complements. Looks good Matt!!

 

Nitto grabbers!! 265-70-17.

 

I had some fun in the sand.

 

2 inch front level kit

 

Did you take off the side panels? Looks nice.

 

What kit is this, Isais? Anybody know if this kit will work on the Pro? I am not upgrading to OME 2" until I wear our current stock shocks.

 

It's just a spacer kit. Look on the ToyTec website. They have a leveling kit made specifically for the pro suspension.

 

Who makes the yellow running lights you have behind the grill?

 

I went with Xenon HID 4300. Fast and easy install and it's very bright.

I was thinking about going with the Kustom 54 Lighting but I couldn't bring myself to spend the money for custom headlights.

 

No turning back now, my wife’s #t4rbeastie got some rock sliders installed permanently. Thanks Adam 4x Innovations for the awesome customer service, and wicked fast shipping. Also special thanks to Travis and Austin w/Absolute Design and Fabrications for the weld job. We are pretty stoked!

 

Got this bad boy bumper built then installed. Long wait on the build, but good things happen to those that are patient....

 

SCS Ray10s with BF Goodrich AT ko2s, stock size 265/70r17 (I realized when I got home that they installed the E rated tires instead of the Cs, so I'm going back to discount tire to get the Cs swapped in. What a pain!). LED fog bulbs in 2700k. Full LED interior lighting. Blacked out Emblems front and back.

Next goal is HID low beams/LED high beams. Then NFAB bars. Then Blistein 6112/5160s... planning on keeping stock height though, as I don't do rock crawling and I want to still be able to park in my garage!

 

It's not much but I turned off that pesky ECO light. Still reading the Manual.

 

That ECO light sucks. More of a distraction than anything and lets face it, we didn't buy our 4Runners for their fuel economy.

 

Installed red D-rings and isolators. Nice look with the red TRD stitching on the seats and my red TRD Off Road badges.

 

New pro wheels and winter tires, Firestone Winterforce 2 UV

 

Nice, loving the dual swing out

 

Killer rig, look is going together well. Why you don’t want the E load?

 

Good looking wheels!

 

added Nfab Nerf Bars last week:

 

very nice!… want one so bad… What brand, Stl. or Alum. and what did you do about rear camera?

 

5100’s and wheelers T1/T13 installed and 285’s wildpeaks installed and aligned. Bottom pic with the old duratracs 265’s.

 

Thanks, it's steel, weighs about 200 lbs, rear camera is at stock location, I can see in between the laddder and tire just fine, well, good enough.

 

Looks good. I have my T1/13 and 5100 setup waiting to go in. 10mm spacers on the driver's side on yours?

 

Yes I have to 10mm spacer on driver side. I wish the rear was a tad bit higher so I might install some OME rear 10mm spacers on each rear coil.

 

Oh really? Looks really good to me. Is there rear rake that isn't visible due to picture angle, or you just want more front rake / more than a leveled look?

 

To me it looks like it sits pretty level but then if you start adding stuff in the rear, it might give it that reverse rake

 

Firestone or airride bags are easy way to avoid butt sag with heavy loads or towing. Install upside down and don't need to take off springs, just jack up and shove through springs. Air line runs out bottom hole. Can run at a few lbs to give 1/2 height but rougher ride.