What have you done to your 5th Gen 4Runner today?

how how was the install? thinking about the anytime front camera, but i wanna relocated the rear camera to be high for when I get an ultra swing.

 

Still waiting on my Transfer Case and Gas Tank skid plates from RCI, and saw that my Dirt Kings should be arriving Thursday. That'll take care of two sets of planned upgrades when they arrive: Armoring the underside, and getting it lifted.

Next up is to assemble some recovery gear. Purchased a set of Apex Overland Front Recovery points, and looking into a receiver hitch recovery point as well.

 

Probably not for everyone but in Chicago not a lot of off-road places.
Added amp steps for short people

 

THANKS!

2018 r1 with 1926 miles when I bought it.

currently has ecu tune, fender eliminator and full titanium Austin Racing Exhaust, sounds like a damn nascar lol

 

Does the supercharger add much pep. Is it worth the money.

 

never seen these. May have to try them for skid plate bolts

 

nice. I had the first of the new gen 2015 r1 in central Texas. Kick myself in the ass for getting rid of it

 

Yeah, bummed I had to get rid of my hog.

 

Please don’t judge. I got a new welder and did my own BMC. My stick welding can use some work. But I tried the best I could with the time that I had and trying not to burn up the rubber so I had to stop a lot. The tight space and weird angles. A mig welder would have been better. Now I just wish Toyota would move that stupid mount backwards as so many people do this mod.

 

nice! where did you order from..

 

went with the bronze trd..going to wrap in falken wild peaks AT3w or hercules terra trac a/t II.. install will be over the weekend..

 

It was time consuming. I spent 12+ hours on everything and still have an issue to resolve that I’ll take care of when my ICS mount comes in and I find time to install it.

I’d set aside a weekend for it. Just have to be methodical with how you want to wire it up.

 

Same here, was about to purchase a much more expensive option and came across these. Wasn't expecting any thread damage, just some dirt. A little WD and a12mm ratchet made short work of it.

 

I ordered it from Auto Anything. Here is the link.

https://www.autoanything.com/air-intakes/spectre-cold-air-intake

 

Neighbor needed to get rid of some dirt and I needed some dirt.

 

New tails or overlays?

 

new tails..

https://www.uniquestyleracingstore....ade-to-2014-style-tail-lights-tlty4run10leds2

 

I drove all the way to Seaside Heights, NJ for my first shot of the coronavirus vaccine! I also stopped by the boardwalk to take a walk and eat some pizza for lunch. Then I went over to Hobbytown in Toms River to pick up some model cement for that 1994 Ricky Rudd Nascar model I got earlier this year and some extra body clips for my RC Trailrunner.

 

Nice looking bike

 

Put some off road tires on that bad boy

 

Parked next to another 4Runner at work

 

Make that rig work

 

I got the Southern Style Offroad slimline bumper, X20 winch and 30" light bar installed this weekend. They had sent me an extra Toyota push switch by mistake but I still went 0 for 2 on the Mictuning brand switches. They work well went not clipped into the dash hole. Once you clip them into place they either only work as a momentary switch or stick on. Ordered some new switches from Air on Board, hoping they are better quality.

 

Bro!

Those are offroad tires!

They're just worn down to slicks!

 

Added a Heretic Studios light bar to the roof.

 

We all had to start somewhere! Looks solid enough, and that’s what counts most.

 

Hampton Roads area?

 

What the heck, what area has snow in late April?