What have you done to your 5th Gen 4Runner today?

Installed some minor mods today. Hooked up the Pedal Commander and promptly went out and played with it. Grinning like a maniac the entire time. I love this thing! Then got the AVS Bugflector II installed, now getting ready to put the screen protector on.

 

I got a Krazy Beaver shovel yesterday, and I took my RC Enduro Trailrunner in the back of my 4Runner this morning. I'm still waiting for Rago molle panel mounts for the shovel. I'm afraid they're not going to come out far enough to fit the shovel, though. I really should have taken a tape measure to the back of my 4Runner Well, maybe I'll just have to get the big Rago shelf.

 

Planned on a full detail today. After the gym, cutting the lawn, and misc. Housework, I added some Lucas fuel injection cleaner and filled up with premium to burn. Opened a bottle of wine and began mental preparation for Monday.

 

Stock set up? Looks good!

 

Thank you, @YetiMtnBkr. Yes, all stock.

 

I also put in my Husky Liners Weatherbeaters, as well as got my NFab Nerf bars installed:


Sadly, I can't use the Husky Cargo Liner I bought, since when I bought it, I didn't know I'd end up buying an SR5 Premium w/3rd row seating. Thankfully, it came with the Toyota Cargo tray.

 

Hopefully, you're not in a rocky situation as those steps will get ripped off or bent up first thing.

 

Picked up a set of Dobinsons drawers semi locally (under 6 hours away counts right?) got them installed. I’m super happy with the drawers. The jury is still out on the wing kit though. I think these were in a 4Runner but running the universal wing kit.



install wasn’t easy but once I got under the truck and found the factory nuts for the cargo tray it was pretty easy / straight forward.

 

We also decided we are going to downsize our fridge. If anyone in the southeast has a cf3 55im and are wishing they had a larger dual zone message me.

 

Not the best picture angle, but was too tired to pull it out of the garage for a proper pic by the time it was done (last night).

Initial install was actually a bit of a pita... though it’s hard to say if it’s really because of victory, or just variations in my frame. It was a super tight fit over my rear frame/crossmember, which made it very difficult to position and lineup. I had to gradually tighten the four main (hitch) bolts in front to get it to sort of squeeze it in, to even get it to where I could start the rear underside bolts. But then it was essentially stuck in that position. It was slightly biased right, but even with loosening every bolt, it wouldn’t budge from that spot at all. Virtually every spot for a bolt also had to be tapped, but that’s mainly just because they’ve been through a couple Michigan winters, so not totally unexpected. After that, the rest was fairly easy.

Happy with end result though, just hope it never has to come back off, lol.

Of course, also added a fold down table for the swing out (second picture). I then also drilled out the antenna mount spot to fit a UHF mount... but need to order a shorter antenna. My old one def wouldn’t clear my garage in this spot. I originally had my antenna on a rago hitch mount, but it would have interfered with the swing out, so it had to go.

 

Second one in a month. Glad I got the warranty last time lol

 

What is it? That looks like a piece of MDF.

 

Installed some Apex Overland Recovery points.

 

Yeah, some sharp ass stone. Waiting for them to replace it still

 

That block under the Sway bar, that's a relocation kit, right? I was thinking about getting that cause I have a little noise but, at least with the one I found on eBay, it said it wouldn't fit a 19 Pro and no TRDs at all.

 

Probably won't work with KDSS-the recovery points don't work with KDSS.

 

Got up to Northstar in Tahoe. Fresh powder and blue skies one day, freezing the next.

 

Installed my Rad Rubber Design engine splash guards and put a few pumps of Mobil1 synthetic grease in my JBA UCA's...

 

The last piece I'm waiting for is the shelf.

 

Yep I got mine from Toytec when I bought my lift.

 

Apex makes them for KDSS

 

Was the screen protector easy to put on? How do you like it so far? I bought same, just got my 4Runner this evening, and will be installing it by this weekend.

 

It was really simple to install, and I like it well enough. However, it is not entirely bubble free as they say on the box. For some reason there's a bubble that formed in mine after applying it that I can not get removed. Thankfully it's not really messing with anything, just kind of annoying seeing it there.

 

Used it to haul home a new Yakima Loadwarrior. Might have to wait for the weekend to actually get it put on.

 

Wouldn't be to concerned. It should go away after a while.

 

Aux battery mount from C4 Fab. Prepping for fridge and possibly solar

 

Rig for red!

 

Astro photography kinda demands it.